Fuel Bowl Heater Element 99-03

Part Number:


(You save $129.62 )

Fuel Bowl Heater Element 99-03 7.3L Powerstroke

Genuine Ford Navistar Fuel Bowl Heater element packaged with 2 new stainless steel hold down screws.
Not aftermarket, OEM manufactured by International.
Contains diagram of heater placement in fuel bowl. For further instructions on removal and installation, refer to the heater section of the fuel bowl rebuild instructions: PDF file to rebuilding your entire fuel bowl.
99-01 Ford Powerstroke: Is you underhood #30 30amp fuse blown, no WTS dash indicater lamp? Chances are you old style heating element has shorted out and taken the fuse with it. This 30 amp fuse also powers the ECM and the truck will not start without it. You can temporarly get by with unplugging the electrical connector from the fuel bowl and replace the 30amp fuse until your new heating element arrives.
Write a Review

12 Reviews Hide Reviews Show Reviews

  • 5
    Genuine factory International fuel bowl heater.

    Posted by Ron Lines on Apr 23rd 2019

    This part is the cheapest one out there AND it is a genuine International factory part. I couldn't be happier. I had the older model 'wire' style ('99 early 250 diesel) and this replaces that old moster perfectly VERY high quality. Works perfectly. You'll never replace it again! GREAT COMPANY TO DEAL WITH.

  • 5
    Navistar heater element

    Posted by Daniel Varro on Apr 22nd 2019

    My original Navistar element lasted 18 years, Don't buy aftermarket, unless you like to have problems.

  • 5
    Definite improvement over the old style element.

    Posted by Jared Recasens on Dec 14th 2017

    International factory part; recently replaced this on my 95 PSD, this will definitely fit the old style “tall” fuel bowl found in the OBS Powerstrokes. Remember the fuel filter stem is LEFT HAND THREAD; fairly simple to install; “tall style” housing will not need the screws, and the heater element will have to be indexed at a certain position to clear a casting nub inside the bowl. Improved fuel, and economy and way better cold starts. Arrived fast, best price around for factory part! GOOD JOB RIFF RAFF.

  • 5
    Great Product!!

    Posted by Muskrat on Nov 20th 2016

    The heating element was an International labeled product. Very robust compared to the original part from 1999. Easy to install and works great.

  • 5
    Definite Upgrade From The Stock Heater Element!!!

    Posted by Kevin on Aug 18th 2016

    I had the fuel bowl out of my '99 Powerstroke to clean it up and replace the o-rings with viton and fluorosilicone components from RiffRaff and discovered that the only thing holding my old element together was one weld/solder joint and the gunk accumulated from the fuel bowl. Lucky for me I discovered this because if it would have shorted out who knows how long it would have taken to track down the problem after the truck quit! This new element is way beefier than the stock part and doesn't look like it would be subject to the same shorting issues prevalent with the old style elements.

    Highly recommended component for replacement or upgrade, and as usual, got the part quickly with no hassle!

  • 5
    Great product

    Posted by Erik on Jan 22nd 2016

    Very happy, great oem replacement, it was even the updated version , and the price was way lower then anywhere else I checked.

  • 5
    Better design than the original

    Posted by Cory on Oct 26th 2015

    My heater was shorting to the fuel bowl and causing some issues with the PCM. Looks like this must have been fairly common because ford changed their design for this one. Great OEM part with a better design than the original.

  • 5

    Posted by Unknown on Apr 14th 2015


  • 4
    Easy Install

    Posted by Bicounty on Mar 13th 2015

    Easy install.Better design than original. Time will tell how long it will last. Don't expect any problems.