Front ABS Grease-able Block Off Fitting 99-16

Part Number:
RDPABS

Manufacturer:

$28.33
$24.82
(You save $3.51 )
(146 reviews) Write a Review
Front ABS Grease-able Block Off Fitting 99-16
  • Write a Review
  • Print

Front ABS Grease-able Block Off Fitting for Ford Super Duty 1999-16

This ABS grease tool will allow you to maintenance your front wheel bearing on the 1999-2016 Dana 50/60 axles. It can be permanently installed for those with only rear ABS or can be used just for greasing then removed.  

- 6061 Billet Aluminum
- Hard Anodized for durability
- Grease Zerk fitting included
- USA Made Viton O-ring for leak-free install
- Made In USA 
- Fitment - 4x4 vehicles 1999-2016 
- Sold Individually

We recommend Lithium-based, non-moly, NLGI #2, GC-LB.  Mobil-1 (red) synthetic grease meets this spec, and is commonly available. Your model may vary so confirm what is needed before proceeding. 

*NOTE: Due to varying models and applications the Dana axle is in we can not guarantee fit or use other than the specific application listed. This product is sold AS IS, with no implied warranties of merchantability for fitness for a particular purpose, unless otherwise required by applicable law. Please review the full terms of sale and warranty before purchase. Your use of this product constitutes acceptance of these terms.

install.jpg

Write a Review

146 Reviews Hide Reviews Show Reviews

  • 5
    It works

    Posted by Rick on Feb 27th 2016

    I saw this while browsing Riffraff. After burning up a bearing, rotor & caliper a few years back I have always worried "when is the next bearing failure" Well not now, this little gizmo works perfect and a surprising amount of grease is allowed to enter. You will need to remove your caliper assembly and put it up onto your leaf spring nearby, then pull off your rotor to get to the sensor. I took apart my hub while I was there and greased up my needle bearings too. Nice product, highly recommended!

  • 5
    Perfect answer

    Posted by Craig on Feb 21st 2016

    Was going to make my own gizmo, then heard about this. It makes the job a cinch. Perfect fit quality build, very happy customer. Just used it today, made the job literally 3 minutes! Highly recommend this.

  • 5
    Perfect

    Posted by Unknown on Feb 21st 2016

    So simple and works perfect. Definitely worth every penny. Telling everyone I know with a super duty about it

  • 5
    Works Perfectly

    Posted by Dave on Jan 31st 2016

    I purchased this not knowing if it would work on my 2008 F-350 SD, 4x4 with manual hubs. and YES, it works perfectly. the hold down screw from the ABS sensor kept it in place while I pumped the hub full of grease.

  • 5
    American Ingenuity

    Posted by Jeff Galacanukus on Dec 28th 2015

    What a great little product. Really a no brainer. $20 to save and extend the life of your 4wd Super Duty wheel bearings. Easy to use. After buying this and experiencing the Riff Raff diesel experience, I am now in line to do the HXR and FXR.
    A+

  • 5
    Awesome product

    Posted by Unknown on Dec 24th 2015

    Another great product from the Riff Raff team. Everyone should have one for their Superduty.

  • 5
    Real Time Saver...

    Posted by Mw Roths on Dec 15th 2015

    Nice product that saves a whole lot of labor (I have done them the hard way a few times.) A must for any Superduty tool box. Love the koozie Clay Thanks...

  • 5
    Awsome

    Posted by Unknown on Dec 15th 2015

    Great made product! If you want your bearings to last you better get one of these!

  • 5
    Way to go Clay

    Posted by Pete Jennings on Dec 13th 2015

    I just used the wheel bearing grease fitting tool that attaches to my ABS sensor.what a great product.It took me less than 30 minutes to grease both sides.Thanks again Clay

Videos